Comparación entre los sistemas de refuerzo TRM y FRP en la prevención del colapso por pandeo de muros de fábrica

E. Bernat-Maso; C. Escrig; L. Gil

doi:10.3989/ic.16.056

Autores/as

E. Bernat-Maso Department of Strength of Materials and Engineering Structures. Universitat Politècnica de Catalunya
C. Escrig Department of Strength of Materials and Engineering Structures. Universitat Politècnica de Catalunya
L. Gil Department of Strength of Materials and Engineering Structures. Universitat Politècnica de Catalunya

DOI:

https://doi.org/10.3989/ic.16.056

Palabras clave:

Tejidos, laminados, refuerzo, experimental, analítico

Resumen

Materiales tipo Fibre Reinforced Polymer (FRP) y Textile Reinforced Mortar (TRM) han sido estudiados, comparados y aplicados para reforzar muros de fábrica de ladrillo. La comparación de su comportamiento frente a efectos de flexión de segundo orden se abordada en este artículo por primera vez. Datos experimentales y analíticos de investigaciones previas y nuevos datos analíticos para los casos de TRM son resumidos, ordenados y sistemáticamente comparados para analizar la respuesta estructural de los muros de fábrica de ladrillo reforzados. Los resultados muestran un comportamiento similar de los dos sistemas respecto su capacidad de carga y su respuesta en el plano. Los casos reforzados con TRM mostraron desplazamientos laterales superiores a los reforzados con FRP.

Descargas

Los datos de descargas todavía no están disponibles.

Citas

(1) Moreno-González, R., Bairán, J.M. (2011). Análisis del comportamiento sísmico de los edificios de obra de fábrica, típicos del distrito Eixample de Barcelona. Informes de la Construcción, 63(524): 21-32. http://dx.doi.org/10.3989/ic.10.045

(2) Garmendia, L., San-José, J.T., García, D., Larrinaga, P. (2011). Rehabilitation of masonry arches with compatible advanced composite material. Construction and Building Materials, 25(12): 4374-4385. http://dx.doi.org/10.1016/j.conbuildmat.2011.03.065

(3) García, D. (2009). Experimental and numerical analysis of stone masonry walls strengthened with advanced composite materials. Bilbao: Escuela de Ingenieria de Bilbao.

(4) Bernat-Maso, E., Gil, L., Roca, P. (2014). Analytical method for the assessment of unreinforced brick masonry walls subjected to eccentric compressive loads. Construction and Building Materials, 73: 180-186. http://dx.doi.org/10.1016/j.conbuildmat.2014.09.105

(5) Papanicolaou, C., Triantafillou, T., Lekka, M. (2011). Externally bonded grids as strengthening and seismic retrofitting materials of masonry panels. Construction and Building Materials, 25(2): 504-514. http://dx.doi.org/10.1016/j.conbuildmat.2010.07.018

(6) Augenti, N., Parisi, F., Prota, A., Manfredi, G. (2011). In-Plane Lateral Response of a Full-Scale Masonry Subassemblage with and without an Inorganic Matrix-Grid Strengthening System. Journal of Composites for Construction, 15(4): 578-590. http://dx.doi.org/10.1061/(ASCE)CC.1943-5614.0000193

(7) Petersen, R.B. (2009). In-plane Shear Behaviour of Unreinforced Masonry Panels Strengthened with Fibre Reinforced Polymer Strips. Newcastle (Australia): University of Newcastle.

(8) Hamed, E., Rabinovitch, O. (2010). Lateral out-of-plane strengthening of masonry walls with composite materials. Journal of Composites for Construction, 14(4): 376–387. http://dx.doi.org/10.1061/(ASCE)CC.1943-5614.0000093

(9) Harajli, M.H., ELKhatib, H., Tomas San-Jose, J. (2010). Masonry Walls Strengthened Using Fibre Textile-Mortar System: Experimental Evaluation of Out-of-Plane Cyclic Response. In CSHM-3 (pp. 19-32). Ottawa-Gatineau (Canada).

(10) Caggiano, A., Martinelli, E., Faella, C. (2012). A fully-analytical approach for modelling the response of FRP plates bonded to a brittle substrate. International Journal of Solids and Structures, 49(17): 2291-2300. http://dx.doi.org/10.1016/j.ijsolstr.2012.04.029

(11) Martínez, S., García, M.D., Gutiérrez, J.P. (2015). Cálculo en agotamiento de secciones de fábrica reforzadas a flexión con láminas de FRP. Informes de la Construcción, 67(540): e118. http://dx.doi.org/10.3989/ic.15.005

(12) Triantafillou, T.C., Papanicolaou, C.G. (2005). Textile reinforced mortars (TRM) versus fibre reinforced polymers (FRP) as strengthening materials of concrete structures. In Proceedings of the 7th ACI International Symposium on Fibre-Reinforced (FRP) Polymer Reinforcement for Concrete Structures, pp. 99-118. Kansas City (USA).

(13) Kurtz, S., Balaguru, P. (2001). Comparison of inorganic and organic matrices for strengthening of RC beams with carbon sheets. Journal of Structural Engineering, 127: 35-42. http://dx.doi.org/10.1061/(ASCE)0733-9445(2001)127:1(35)

(14) Toutanji, H., Deng, Y. (2007). Comparison between organic and inorganic matrices for RC beams strengthened with carbon fiber sheets. Journal of Composites for Construction, 11(5): 507-513. http://dx.doi.org/10.1061/(ASCE)1090-0268(2007)11:5(507)

(15) Papanicolaou, C.G., Triantafillou, T.C., Karlos, K., Papathanasiou, M. (2006). Textile-reinforced mortar (TRM) versus FRP as strengthening material of URM walls: in-plane cyclic loading. Materials and Structures, 40(10): 1081-1097. http://dx.doi.org/10.1617/s11527-006-9207-8

(16) Papanicolaou, C.G., Triantafillou, T.C., Papathanasiou, M., Karlos, K. (2007). Textile reinforced mortar (TRM) versus FRP as strengthening material of URM walls: out-of-plane cyclic loading. Materials and Structures, 41(1): 143–157. http://dx.doi.org/10.1617/s11527-007-9226-0

(17) Bernat, E., Gil, L., Roca, P., Escrig, C. (2013). Experimental and analytical study of TRM strengthened brickwork walls under eccentric compressive loading. Construction and Building Materials, 44(0): 35-47. http://dx.doi.org/10.1016/j.conbuildmat.2013.03.006

(18) Bernat-Maso, E., Gil, L., Escrig, C. (2015). Analysis of brick masonry walls strengthened with fibre reinforced polymers and subjected to eccentric compressive loads. Construction and Building Materials, 84: 169-183. http://dx.doi.org/10.1016/j.conbuildmat.2015.02.078

(19) Bernat-Masó, E. (2014). Analysis of unreinforced masonry walls under eccentric axial load. Saarbrücken (Germany): Scholar's Press.