Un estudio histórico del problema de las piezas prismáticas rectas sometidas a compresión. Parte II

Autores/as

  • Miguel A. Ortega Dr. Ingeniero de Caminos. Empresarios Agrupados. Departamento Civil
  • José L. Romero Dr. Ingeniero de Caminos. Facultad de Informática. UPM
  • Emilio de la Rosa Dr. Ingeniero de Caminos. E. T. S. de Ingenieros de Caminos. UPM

DOI:

https://doi.org/10.3989/ic.2007.v59.i508.583

Palabras clave:

elementos finitos, métodos numéricos, pandeo, pilares, splines generalizados

Resumen


Se complementa la primera parte de este trabajo con un breve repaso histórico de algunos de los modelos teóricos y métodos numéricos empleados en la resolución de los problemas planteados en el artículo anterior, cuando no ha sido posible su descripción analítica.
En un primer apartado se mencionan algunos de los métodos que se han utilizado para abordar las ecuaciones que rigen los modelos: analíticos con soluciones cerradas, aproximados, matriciales, elementos finitos y splines generalizados. En un segundo apartado se enumeran distintas técnicas numéricas empleadas para la determinación de los aspectos que describen los problemas en relación con las vigas-columna: deformadas, esfuerzos, trayectorias, puntos límite y críticos, etc.

Descargas

Los datos de descargas todavía no están disponibles.

Citas

(1) Aas-Jakobsen, K. and Grenacher, M.: “Analysis of Slender Reinforced Concrete Frames”. IABSE, Publications. 1974.

(2) Alemdar, B. N. And WHITE, D. W.: “Displacement, Flexibility, and Mixed Beam-Column Finite Element Formulations for Distributed Plasticity Analysis”. Journal of Structural Engineering. ASCE. December 2005.

(3) Argyris, J. H.: ´’Recent Advances in Matrix Methods of Structureal Analysis’´. Pergamon Press. 1964.

(4) Argyris, J. H.: “Continua and discontinua”. Proc. Onf. Matrix Methods in Struct. Mech., Air Force

(5)Inst. of Tech. Wright Patterson Air Force Base, Ohio. 1965.

(6) Bazant, Z. P. and Cedolin, L.: ´’Stability of Structures’´. Oxford University Press, 1991

(7) Brebbia, C. and Connor, J.: “Geometrically non-linear fi nite element analysis” Proc. ASCE J. Engng Mech. Div., Proc. 1969.

(8) Chen, W. F., Goto, Y. and Liew, J. Y. R.: “Stability design of Semi-Rigid Frames”. John Wiley and Sons. 1996.

(9) Cheong Siat MOY, F.:”General Analysis of Laterally Loaded Beams Columns” Journa of the Structural Division. ASCE, Vol. 100 No ST6 Proc Paper 10625 (1975).

(10) Chen, W. F. and Atsuta, T.: ´´Theory of Beam-Columns´´. Vols.1, 2, McGraw-Hill, 1976.

(11) Chen, W. F. and Thomas, S.: ´’Advanced Analysis of Steel Frames’´. CRC Press,1994.

(12) Chwalla, E: “Theorie de aussermittig gedrückten Stabes aus Bausthal”. Der Stahlbau. 1934.

(13) Davidenco, D. F.: “On a New Method of Numerical Solution or Systems of Nonlinear Equations”. Dokl. Akad. Nauk. USSR, 88, 601-602. 1953.

(14) Disque, R. O.: ´´Applied Plastic Design in Steel´´. Van Nostrand Reinhold Co. 1971. FELIPPA, C. A.: ´´Introduction to the analysis of nonlinear elastic structures by the Finite Element Method´´. University of Colorado at Boulder.

(15) Galambos, T. V.: ´´Structural Members and Frames.´´ Prentice-Hall, Inc. 1968.

(16) Gallager, R. J. and Padlog, J.: “Discrete element approach to structural stability”. Am. Inst. Aero.& Astro. J. 1(6), 1437-1439.1966.

(17) Gallager, R. J., Gellatly, R. A. PADLOG, J. and MALLET, R. H.: “A discrete element procedure for thin shell instability analysis”. Am. Inst Aero. & Astro. J., 5 (19), 138-145. 1967.

(18) Haselgrove, C. B.: “The solution of Nonlinear Equations and of Differential Equations with Two- Points Boundary Conditions”. Computer J., 4. 255-259. 1961. doi:10.1093/comjnl/4.3.255

(19) Holand, I. and Moan, T.: “The fi nite element in plate bukling”. Finite Element Method. In Stress Analisys, ed. I. Holand et al., Tapir. 1969.

(20) Jennings, A.: “Frame analysis Including Change of Geometry”, Journal of the Structural Division, ASCE, Vol. 94. Pp. 627-644. 1968

(21) Kapur, W. W. and Hartz, B. J.: “Stability of plates using the fi nite element method”, Proc. ASCE, J. Engng. Mech, 92, EM2, 177-195 1966.

(22) Karmán, T. V.: “Untersuchungen über Knickfestigkeit. Mitteilungen über Forschungsarbeiten auf dem Gabiete des Ingenieurwesens”. 1910

(23) Kawano, A. and Warner, R. F.: “Nonlinear Analisys of the Time Dependent Behaviour of Reinforced Concrete Frames”. Research Report Nº R125, Dep. of Civil and Environemental Engineering, The University of Adelaide. 1995.

(24) Klopfestein, R. W.: “Zeros of Nonlinear Functions”. J. ACM, 8. 366-373.1961.

(25) Mallet, R. H. and Marcal, P. V.: “Finite element Analysis of non-linear structures”. Proc.ASCE, J. Engng. Mech.94, ST9, 2081-2105. 1968.

(26) Marcal, P. V.: “Finite element Analysis with material non-lineearities-theory and practise”. Recent Advances in Matrix Methods of structural Analysis and Design, ed. R. H. Gallager et al. The University of Alabama Press pp. 257-282. 1971.

(27) Murray, E. W. and Wilson, E. L.: “An approximate non-linear analysis of thin-plates”. Proc. Air Force 2nd Conf. On Matrix Meth. In Struct. Mech., Srigth-Patterson Air Force Base, Ohio. 1968.

(28) Nayak, G. C. and Zienckiewicz, O. C.: “Note on the “alpha-constant” stiffness method of the analysis of non-linear problems”. Int. J. Num. Meth. In Engng., 4, 579-582. 1972.

(29) Oden, J. T.: “Numérical formulation of non-linear elasticity problems”. Proc. ASCE, J. Struct. Div. 93, ST3, paper 5290. 1967.

(30) Oden, J. T.: “Finite element aplications in non-linear structural analysis”, Proc. Conf. On Finite Element aplications in non-linear structural analysis”. Proc. Conf. On Finite element Meth. Vanderbilt University Tennessee. 1969.

(31) Ortega, M. A.: ´’Análisis del pandeo de pilares en régimen no lineal mediante splines generalizados. ´´ Tesis Doctoral, E. T. S. Ingenieros de Caminos, UPM. 2004.

(32) Riks, E.: “The Application of Newton´s Method to the Problem of Elastic Stability”. Trans. ASME, J. Appl. Mech. (1972).

(33) Riks, E.: “An incremental approach to the solution of snapping and bukling problems”. Int. J. Solids and structs. 15, 529-551. 1979.

(34) Ros, M. and Brunner, J.: “Die Knicksicherheit von an beiden Enden gelenkig gelagerten Stäben aus Konstruktionsstahl”. Eidg. Materialprüfungsanstalt an der E.T.H. 1926

(35) Romero, J. L., Ortega, M. A. y CORRALES, J. M.: “Estudio y resolución del modelo de viga de Timoshenko. Algoritmo de acciones equivalentes”. V Congreso de Métodos Numéricos en Ingeniería. Madrid, 3-6 de Junio de 2002

(36) Romero, J. L. y ORTEGA, M. A.: “Acciones equivalentes y solución en desplazamientos interpolada en la viga de Bernoulli-Euler”. Informes de la Construcción, Vol. 49. N0 454, pp. 5-27,1998.

(37) Romero, J. L. y ORTEGA, M. A.: “Splines generalizados y solución nodal exacta en el método de elementos fi nitos”, Informes de la Construcción, Vol. 51. Nº 464, pp. 41-85, 1999.

(38) Sabir, A. B. and Lock, A. C.: “The application of fi nite elements to the larger-defl ection geometrically non-lineart behaviour of cylindrical shells”. Proc. Int. Conf on Var. Meth in Engng., Southampton Univ., Session VII, 67-76 1972

(39) Sun, C. H., Bradford, M. A. and Gilbert, R. I.: “A Reliable Numerical Method for Simulating the Post-Failure Behaviour of Concrete Frame Structures”. Computers and Structures. 1994.

(40) Sharifi, P. and Popov, E. P.: “Non linear buckling analysis of sandwich arches”. Proc. Asce, J. Engng Mech. Div, 97. 1397-1411. 1971.

(41) Turnner, M. J., Dill, E. H., Martin H. C. and Melosh, R. J.: “Large defl ection analysis of complex structures subjected to heating and external loads”. J. Aerospace Sci., 27. 1960.

(42) Wempner, G. A.: “Discrete Approximations Related to Nonlinear Theories of Solids”. Int. J. Structures. (1971).

(43) Westergaard, H. M. and Osgood, W. R.: “Strength of Steel Columns”. Trac. Of the Amer. Soc. of Mech. Engineers. 1928.

(44) Wong, K. W. and Warner, R. F.:”Non-linear analysis of concrete frames using direct stifness line element approach”. Research Report Nº R-158. Department of Civil and Environmental Engineering. University of Adelaide. 1997.

(45) Wong, K. W., Yeo, M. F. and Warner, R. F.: “Non-linear Behaviour of Reinforced Concrete Frames”. Civil Engineering Transctions, Institution of Engineers, Australia. 1988.

(46) Zienckiewicz, O. C.: ´’El método de los Elementos finitos’´. Reverte. 1982.

Descargas

Publicado

2007-12-30

Cómo citar

Ortega, M. A., Romero, J. L., & de la Rosa, E. (2007). Un estudio histórico del problema de las piezas prismáticas rectas sometidas a compresión. Parte II. Informes De La Construcción, 59(508), 61–71. https://doi.org/10.3989/ic.2007.v59.i508.583

Número

Sección

Artículos